Studio projects c1

Brighter and louder than an AKGmore mid punch than an Audio Technica the C1 straddles the versatility curve like a drunk Texas girl on a mechanical bull. The Thing that you have to remember with most musical gear is that every single piece has its own intrinsic sound quality.

Studio projects c1

FM Transmitters Studio projects c1 microtransmitter that can cover 3km range. In our case the output power is about mW depending on the input power of 10mW and 9V battery power supply. The transistor Q1 must be mounted with a heatsink, the heatsink must have small dimensions cylindrical in order not to increase the parasitic capacitance.

The trimmer R2 serves to adjust the bias of the transistor, Studio projects c1 with the trimmer fully open and close by measuring the current absorbed by the 9V, in my case you get mW at the output with a current of 50mA not increase this value as you only increase the absorption by heating the transistor without increasing output power, because the input power is too low.

Clearly the 9V battery will be able to provide 50mA only for a few hours, if necessary have greater autonomy should be used a larger battery, but it is no longer a bug but simply an FM transmitter.

FM Transmitters This tiny Mhz FM transmitter bug measures just 10mm x 17mm in size and as you can see in the photos the biggest components are just the microphone and the battery. You can use a small microphone from an older cell phones, they are small in size and have an excellent sensitivity.

For an effective power supply the 9V battery Duracell is excellent and allows several hours of battery life, but if you want to have a smaller size it is better to use 2 or 3 lithium cells like the used in PCs. The circuit works well from 3 to 12V, the maximum range is obtained with 12V and a piece of cm cable as an antenna.

It started with a self-build kit from the Danish manufacturer Jostykit that allowed everyone to build a small FM transmitter for a few Euros. Such transmitters generally consist of a single transistor oscillator with a simple resonance circuit, sometimes with an extra transistor that is used as audio pre-amplifier.

The image shows a few examples that were available in European electronics shops in the mid s. The transmitter shown here was built in the mids and measures just 1 x 2 cm. When properly built, it may have a range of several kilometers. You may use it to run your own private neighborhood radio, just replacing the microphone capsule with a male audio jack connected to your pc or MP3 player.

You may also use this as a spy transmitter, but be reasonable in that case. It's rated for 1 Watt, so you can listen to it even from a few kilometers, with a good antenna and not too much obstacles in the way.

Studio projects c1

The circuit is based on LM positive and LM negative voltage regulators. LM series of adjustable 3 terminal regulator is capable of supplying in excess of 1. But the frustrating part is most transmitters refuses to work at all, and secondly the internet is full of crappy transmitter circuits.

Designing a stable FM transmitter circuit is rather a difficult job, many calculations are involved their. There are also some construction error and component value tolerance.

Here you can find a reasonably stable and well tested transmitter that actually works. You don't have to understand the precise working of the transmitter to build it.

But some basic information won't harm. A transmitter alone is, as you probably know, is not enough to start your radio station.

Studio projects c1

In the simplest form you need 4 things. First an input device such as an amplifier you also use with your home stereo. You need a regulated power supply. In this case a Volts 2. One of the most influential things you need is antenna and coax cable. And finally the transmitter itself.

Transmitter is divided into two main parts; the oscillator and the amplifier. The oscillator converts electric sound information into electromagnetic waves. The amplifier gives these waves a bigger amplitude.

The Studio Projects C1

Power Supplies A constant current source source can supply a fixed current to a load regardless of input voltage or load change. The LM is quite useful as a constant current source, works on a wide input voltage range, from 3V up to 40V.

The circuit is rather simple, uses only one transistor and few passive components and performs well in terms of frequency stability, almost zero drifting after about 4 hours of continuous operation. With 12 volt DC it will deliver 1 watt RF power.

The most important parts of the oscillator are the transistor Q1 and the tuned circuit, which comprises the inductor Ll and the variable capacitor CV1.Find great deals on eBay for studio projects c1. Shop with confidence. Written by Rip RowanOriginally published May 31, Probably the hottest product to hit the audio world lately has been the Studio Projects line of.

Relive the moment. Vuze camera, powered by Humaneyes, is the world’s first consumer virtual reality 3D camera and integrated Studio with super-simple automatic VR movie production. If you want a copy, the fastest way of doing this would be to save the project.

Then make a copy of the entire thing on the File System. Go back into Visual Studio and open the copy. The C1 has a fixed cardioid pattern. Photo: Mike Cameron Studio Projects are based in California, but, in common with many other companies offering low-cost capacitor microphones, the manufacturing is actually undertaken in China, in .

Building Python with Visual Studio or 7th revision, August 7, A document history can be found at the very end of this page.

ph-vs.com - Electronic Projects, Electronic Schematics, DIY Electronics